Slip Hazards? Think Tough.

Think Grip. Think Dino Grip

Call us now!
407 413 5737

items(s) | $0.00

FRP Anti-Slip Flat Sheet

Availability: In stock

(exc Tax)
$213.84

* Required Fields

Information

Dino Grip Anti-Slip Flat Sheets are prefabricated fiberglass panels that provide an instant non-slip surface to a variety of substrate. 

Dino Grip Anti-Slip Flat Sheets are produced in 2.4m x 1.2m panels and are ideal for installation on walkways, ramps, gangways, factory floors and many DIY applications.  They offer extreme slip resistance and can also be installed onto a variety of substrates including traditional steel checker plate, which are notoriously slippery when wet.

Dino Grip Anti-Slip Flat Sheet are manufactured from FRP (fiber reinforced plastic) / GRP (glass-fiber reinforced plastic) to provide an extremely tough and durable product.  These types of products have been used in the most testing environments.  

Dino Grip Anti-Slip Flat Sheet is the ultimate choice for dealing with potential slip hazards.  The finished system provides a high slip resistance in wet or oily conditions. 


Available in one standard size and one width. Need a different size? Call us to ask about our FREE custom cutting service!

Disclaimer:

DinoGrip will not be responsible for shade or color variation caused by application or substrate deficiencies, or fading resulting from natural causes such as weather.

  • Adhesive Required
  • Anti Slip
  • DIY Installation
  • Foot Traffic
  • Indoor Use
  • Outdoor Use
  • Screw Driver Attachment
  • Spring Loaded Rivet Gun

  • Anti-Slip Surface

  • Hard Wearing & Durable

  • Installs over Virtually any Substrate

  • Choice of sizes 

  • Black
  • Yellow
  • Red

Fixings

Stainless Steel Screws

Dino Grip recommends standard flanged stainless steel screws which therefore do not rust or stain the decking and do not create a trip hazard.Please see our Fitting and Adhesives page for more information. 

Color Headed Screws

Alternatively Dino Grip can provide our color headed flanged screws that are available in black to match the Flat Sheet.

The advantage of using these particular screws is that they have an T-Star head which makes for easier installation as they do not round the heads off during installation.

For metal surfaces, we would recommend securing the sheets using rivets.

Anti-Skid

Dino Grip Step Covers are a pre-formed fibreglass fiberglass tread which has an Anti-Skid gritted top to provide an a superb Skid-Resistant and hard-wearing surface.  They exceed the coefficient of friction requirements for slip prevention established for both OSHA and ADA regulations.

Durable

Dino Grip Flat Sheet are manufactured from FRP (fiber reinforced plastic) / GRP (glass-fiber reinforced plastic) to provide an extremely tough and durable product.

Corrosion Resistant

Dino Grip Flat Sheets are resistant to a wide range of chemicals and are perfectly suited for use even in the most extreme environments. Chemical resistance guides are available on request. 

Do It Yourself Installation

Dino Grip Flat Sheet allows it to be applied to almost any surface such as concrete, steel or wood. The fact that it is supplied as a finished product means that it can be walked on immediately after installation thus keeping disruption to a minimum. This product is ideal for do it yourself installations.

Aesthetics

Dino Grip Flat Sheet provides an instant aesthetically pleasing non-slip finish to any surface.

SAFETY

When installing Dino Grip Flat Sheet we  recommend that PPE (personal protective equipment) is worn. 

Cutting the Flat Sheet

If you need to cut the Flat Sheet to size during your installation, we would recommend that a suitable dust mask with protective safety goggles and gloves are worn.  The Flat Sheet should be cut externally or in well ventilated areas. If using a circular saw or angle grinder, use a standard carbon or diamond blade when cutting them to size.

Dust residue can be disposed of using normal waste disposal methods. No special permissions or licenses are required.

Installation of Flat Sheet

During the installation of the Flat Sheets we would recommend that safety gloves and glasses are worn as the product has a textured anti-slip finish and whilst screwing the Flat Sheet into place, it is recommend that you wear safety glasses or goggles.

PREPARATION

Dino Grip recommends that the surface is firstly swept and cleaned ensuring that the surface is suitable to receive the Flat Sheet. 

INSTALLATION

Wooden Surfaces

To lay the Flat Sheets upon the surface and then use a 6mm masonry drill bit to drill the top of the gritted surface in the desired fixing locations.  We would recommend that there are approximately 20 fixings per Flat Sheet; however this would depend on the usage and installation location.

Once the pilot holes have been drilled to then screw into position using the flanged stainless steel screws.

Additional adhesive can be used (if require) to add extra grip to the underneath the Flat Sheet.

Metal Surfaces

To lay the Flat Sheets upon the surface and then use a 7/32" (6 mm) masonry drill bit to drill the top of the gritted surface only in the desired fixing locations.  We would recommend that there are 20 screws/rivets per sheet.  Change the drill bit to a 13/64" (5 mm) metal drill bit.  Use drilling compound, and then proceed to drill the metal surface under the Flat Sheet – the Flat Sheet can be kept into position during this process as you have already pre-drilled the Flat Sheet. 

Place rivet into hole and use a rivet gun to fix into position.  Please ensure that all rivets have been compressed. 

Additional adhesive can be used (if required) to add extra grip to the underneath of the Flat Sheet.

Concrete Surfaces

To lay the Flat Sheet upon the surface use a 7/32" (6 mm) masonry drill bit to drill the top of the gritted surface and into the underlying concrete sub-base only in the desired fixing locations.  We would recommend approximately 20 screws per Flat Sheet; however this would depend on the usage and installation location.  Remove the Flat Sheet and re-drill the concrete fixing points with an 5/16" (8 mm) masonry drill bit. 

Introduce plastic anchors into the holes in the concrete surface and place the Flat Sheet into place and screw into position using the flanged stainless steel screws.

Additional adhesive can be used (if required) to add extra grip to the underneath of the Flat Sheet.

Additional Adhesive

While mechanical fixings are all that is required to secure the Flat Sheet, wherever possible, the application of an appropriate high strength gap filling adhesive will provide the following benefits:

A secondary fixing in the event that the mechanical fixings should fail.

A barrier against the "Drumming" noise that is created when fitting over the existing substrate.

 

Apply a 1/4" (6 mm) bead of high strength gap-filling adhesive around the periphery of the Flat Sheet and in horizontal stripes at approximately 7.9" centers. Immediately press the Flat Sheet firmly to the substrate to ensure adequate transfer of adhesive. Secure with the screws or rivets and allow the adhesive sealant to cure before allowing excessive traffic to use the areas. A firm bond will b achieved in about one hour under normal conditions.

RECOMMENDED MECHANICAL FIXINGS

Recommended fixings
Over Timber
No 20 x 4.8mm x 38mm – Flanged Stainless Steel Screws


Over Steel Plate
No 20 x 20mm Flanged headed rivets

Over Concrete
No 20 x Brown Raw Plugs (or equivalent)
No 20 x 4.8mm x 38mm – Flanged Stainless Steel Screws


Over Open Mesh
Stainless steel or zinc plated saddle clips and domed head bolts suitable in length for the depth of the existing treads.

CLEANING GUIDE AND TIPS


While Flat Sheets are extremely resilient to dirt and contaminations it will require minimal maintenance.

Dry dirt and debris can easily be removed using a stiff brush and should be carried out on a regular basis.

If the Flat Sheets have been subjected to spillages or the dirt has become embedded, detergents can be used. It is always advisable to test any cleaning product on the Flat Sheets an inconspicuous are before starting the cleaning procedure.

Using the detergent, warm water and a stiff bristle brush; scrub the affected areas until clean. The excess water can be removed using a wet/dry vacuum cleaner or power washer.

Where circumstances allow, the Flat Sheet can be power washed without causing harm. Care should be taken when the Flat Sheet has been stuck down and / or edge sealed as very high pressure power washing or repeated power washing could cause damage to sealants and adhesives.

GENERAL ROUTINE MAINTENANCE

The security of the mechanical anchors / adhesives should be checked on a regular basis. Circumstances will vary, based upon the volume of foot traffic etc. but, as a guide, monthly inspections would be advisable in high traffic areas.

 

 

CHARACTERISTICS

  • Slip Resistant Surface
  • Impact Resistant
  • Class 1 Flame Spread – Non Sparking
  • Corrosion Resistant
  • Lightweight
  • Non Metallic
  • Tough & Durable
  • Can be Cut to Size
  • Quick Installation
  • Manufactured to ISO 9001

APPLICATIONS

Ideal for the installation on any surface to provide an instant non-slip surface.

TECHNICAL DATA

Description

Slip Resistant Decking Profiles

Top Finish

Carbon and Silicon Grip Top Surface

Stock Colours

Black

Thickness

Nominally 4mm Thick

Chemical Resistance

Different Chemical Resistance Available, Please Call our Technical Department for Advice.

Panel Size

2400mm x 1200mm

Landing Cover Weight

8.1kg

Service Temperatures

-20°c  to + 80°c

Load capabilities

Credited with no load bearing strength

Design Life

10+ Years (subject to traffic analysis)

General Use

Standard Pedestrian Traffic



SLIP RESISTANT LEVELS


Measured using the Pendulum test method (Four S rubber slider / 96 Slider) – standard simulated shoe sole.

Top Surface

Dry Reading

Wet Reading

Standard Grit Surface

80

75


The UK Slip Resistance Group guide to slip resistance of a floor for able-bodied pedestrians.

Four S Pendulum Value

Potential for Slip

Above 65

Extremely Low

35 to 65

Low

25 to 65

Moderate

25 and Below

High


To ensure that the above slip resistant levels are maintained the Flat Sheet should be kept clean in accordance with the attached cleaning guide and tips.

 

Additional Information

Install Videos No